|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Voltage Variable Absorptive Attenuator DC - 2 GHz Features q q q q q q q q AT-250 V 2.00 SO-8 12 dB Voltage Variable Attenuation Low Intermodulation Products Low DC Power Consumption: 50 W Single Voltage Control 0 to -4 Volts Nanosecond Switching Speed Temperature Range: -40C to +85C Low Cost SOIC 8 Plastic Package Tape and Reel Packaging Available1 Description M/A-COM's AT-250 is a GaAs MMIC voltage variable absorptive attenuator in a low cost SOIC 8-lead surface mount plastic package. The AT-250 is ideally suited for use where attenuation fine tuning, fast switching and very low power consumption are required. Typical applications include radio, cellular, GPS equipment and other Automatic Gain/Level Control circuits. The AT-250 is fabricated with a monolithic GaAs MMIC using a mature 1-micron process. The process features full chip passivation for increased performance and reliability. Ordering Information Part Number AT-250 PIN AT-250TR AT-250RTR Package SOIC 8-Lead Plastic Package Forward Tape & Reel Reverse Tape & Reel Electrical Specifications, TA = +25C Parameter Insertion Loss Test Conditions2 DC - 0.1 GHz DC - 0.5 GHz DC - 1.0 GHz DC - 2.0 GHz DC - 0.1 GHz DC - 0.5 GHz DC - 1.0 GHz DC - 2.0 GHz 10% to 90% RF, 90% to 10% RF 50% Control to 90% RF, 50% Control to 10% RF In Band Linear Operation Absolute Max Input Power Measured Relative 0.05 GHz to Input Power 0.5 - 2.0 GHz (For two-tone Input Power Up to +5 dBm) Measured Relative 0.05 GHz to Input Power 0.5 - 2.0 GHz (For two-tone Input Power Up to +5 dBm) Unit dB dB dB dB dB dB dB dB nS nS mV dBm dBm dBm dBm dBm 28 40 18 18.5 Min. Typ. 2.9 3.0 3.2 3.4 +/- 0.1 +/- 0.2 +/- 0.5 +/- 1.2 2.1:1 3 5 10 Max 3.1 3.2 3.5 3.8 +/- 0.3 +/- 0.4 +/- 0.8 +/- 1.5 Flatness (Peak to Peak) VSWR Trise, Tfall Ton, Toff Transients Power Handling IP2 IP3 13 21 34 47 31(3) 36(3) 1. Refer to "Tape and Reel Packaging"Section, or contact factory. 2.All measurements at 1 GHz in a 50 system, unless otherwise specified.A control voltage 0 to -4 volts @ 20 A typ. 3. For levels above 6 dB attenuation. For levels below 6 dB, the minimum specification numbers apply. Voltage Variable Absorptive Attenuator Absolute Maximum Ratings1 Parameter Max. Input Power Control Voltage Operating Temperature Storage Temperature Absolute Maximum +21 dBm +5 V, -8.5 V -40C to +85C -65C to +150C AT-250 V 2.00 Functional Schematic 1.Operation of this device above any one of these parameters may cause permanent damage. Typical Performance Pin Configuration Pin No. 1 2 3 4 5 6 7 8 Description RF1 GND GND A GND GND GND RF2 |
Price & Availability of AT-250 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |